DMP Electronics XR500 Manuel d'utilisateur télécharger pdf (Page 65)

Digital Monitoring Products XR500 Series Canadian Programming Guide

zone informaTion

FA Series Wireless

For an FA Series Remote Wireless ReceiversettheHouseCodeto99.SeeHouseCodeprogrammingin

SystemOptions.Onlyzones500to699canbeprogrammedasFASeriesWirelesszonesformaximumof

200WirelessZones.

For a DMP 1100X Wireless Receiver see section 16.10.

19.12

ZONE INFORMATION

WIRELESS? NO YES

Wireless

SelectYEStoprogramawirelesszoneconnectedtoanFASeriesFA400-DMPRemote

WirelessReceiver.PresstheCOMMANDkeytocontinuewithwirelessprogramming.

19.12.1

CHECK IN TM: 60

Check-in Time

Youcansetwirelesstransmitterstocheckinautomaticallyevery10,30,or60

secondsornotatall.Tochangethe60seconddefault,pressanytoprowSelect

keytodisplayNONE103060.Selectthecheck-intimeyouwantforthiszone.

Note:RefertotheWirelessCheck-inandSupervisionTimeDenitionssectionof

the Appendix for supervision information.

19.12.2

INT CONT NO YES

Internal Contact

SelectYEStouseaninternalcontactonthewirelesstransmitter.SelectNO

touseanexternalcontact.WhenyouselectNO,thefollowingtwoprompts

display.

19.12.3

EOL NO YES

End-of-Line

Select YES to supervise an external contact connected to the wireless

transmitter.Atthecontact,installa2.2kOhmEnd-of-Lineresistorinparallel

forNormallyOpencontactsandinseriesforNormallyClosedcontacts.

19.12.4

NRM OPEN NO YES

Normally Open

SelectNOifthecontactconnectedtothewirelesstransmitterisNormally

Closed.

19.12.5

NEXT ZONE NO YES

Next Zone

SelectYEStoreturntotheZONENO:-prompttoprogramanewzone.Select

NOtodisplaytheAlarmActionoption.

19.13

ALARM ACTION . . . .

Alarm Action

ThisoptionallowsyoutochangeanyZoneTypestandarddenitions.WhentheZone

Typeisspecied,theAlarmActionforthatzoneisstoredinmemory.

IftheZoneTypeisBlank,Night,Day,Exit,Auxiliary1,orAuxiliary2itisa

non-24-hourzoneandtheAlarmActionprogramingbeginswithDisarmedOpen.

IftheZoneTypeisFire,Panic,Emergency,orSupervisoryitisa24-hourzonethatis

alwaysarmedandtheAlarmActionprogrammingbeginswithArmedOpen.

TheFireVerifyZoneTypefunctionsthesameasFireType,withthefollowing

exceptions:WhenaFireVerifyzoneinitiatesanalarm,thepanelperformsaSensor

Reset. If any Fire Verify zone initiates an alarm within 120 seconds after the

reset, an alarm is indicated. If an alarm is initiated after 120 seconds, the cycle is

repeated and a zone fault report is sent to the receiver.

DoNOTprogramFireVerifyZoneTypesforZoneRetard.

19.14

DISARMED OPEN

Disarmed Open

Denestheactiontakenbythepanelwhenthezoneisopenedwhiletheareais

disarmed.Therearethreeactionstodene:Reporttotransmit,RelayOutputto

activate,andRelayOutputaction.

YoumustalsomaketheseselectionsfortheDisarmedShort,ArmedOpen,andArmed

Shortzoneconditions.PressCOMMANDtocontinue.

1 2 ... 60 61 62 63 64 65 66 67 68 69 70 ... 83 84

Commentaires sur ces manuels

Pas de commentaire

DMP Electronics XR500 Manuel d'utilisateur Page 65

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité DMP Electronics XR500